TRAINING NATURAL GAS ENGINEERING PROPERTIES ESTIMATION AND PIPE LINE NETWORK DESIGN FOR DISTRIBUTION AND PROCESSING
TRAINING ESTIMASI PROPERTI MEKANIK GAS ALAM DAN DESAIN JARINGAN PIPA UNTUK PENDISTRIBUSIAN DAN PROSES
TRAINING PENGGUNAAN PROSES TERMODINAMIKA
Training Objective.
After completing this training, you should able to do the following :
- Apply the concept of thermodynamic including mixing rule (volumetric properties of mixture) to calculate the properties of Natural Gas.
- Predict the condition of hydrate formation and know the method to prevent it
- Apply the concept of fluid flow to calculate the parameters used in sizing the Natural Gas lines
- Recognize the use of non pipe elements and to calculate the parameters which fit the elements to the pipe line.
- Formulate equations for steady-state analysis
- Use graph theory to design and estimate, and optimize gas networks
- Doing troubleshooting of gas networks
Day 1
- Thermodynamic Aspect of Real Gas
- The Law of Thermodynamics in relation to energy balance
- Volumetric Properties of Pure Substances: Cubic Equations of State
- Volumetric Properties of Pure Substances: The Virial Equations
- Generalized Correlations for Gases
- Volumetric Properties of Mixtures
- Behavior of Ideal Gas
- Ideal Gas Mixtures
- Behavior of Real Gases
- Effect of Non-hidrocarbon component on Z-Factor: Wichert-Azis Correction Method
- Effect of Non-hidrocarbon component on Z-Factor: Carr-Kobayashi-Burrow Correction Method
- Effect of Non-hidrocarbon component on Z-Factor: Correction Method for high-molecular weight gases
- Direct Calculation of Compressiblity Factors using several methods including Papay, Hall-Yarborough, Dranchuk-Abu-Kassem, Dranchuk-Parvis-Robinson and Hankinson-Thomas-Phillips Methods
Day 2
- Properties of Natural Gas I: Thermodynamic Properties of Natural Gas
- Compressibility of Natural Gases
- Gas Formation Volume Factor
- Properties of Natural Gas II: Estimation of the Viscosity of Gases
- Carr-Kobayashi-Burrow Method
- Leo-Gonzalez-Eakin Method
- Dean and Stiel Method
- Gas Hydrates and Their Prevention
- Water content in natural Gas
- Water-Hydrocarbon systems: Gas Hydrates
- Prediction of Conditions for Hydrate Formation
- van der Waals-Platteeuw Model
- Gas Expansion-Joule Thomson Cooling
- Use of Methanol to Prevent Hydrates
- Hydrate in the Earth
Day 3
- Fundamental of Gas Flow in Pipe line
- Application of Flow Equation
- Calculation of Static Bottom Hole Pressure
- General Flow Equation
- Flow Equations in Practice: Gas Flow Characteristic in Pipes
- Flow Equations in Practice: Efficiency Factor
- Flow Equations in Practice: Common flow equation
- Non-Pipe Elements in Gas Networks
- Compressor Stations
- Pressure Regulators: Direct operated gas Regulators
- Pressure Regulators: Pilot-loading gas regulators
- Valves
- Selected Elements of Graph Theory
- Terms and Definitions in Graph Theory
- Network Topology: The Branch-Nodal incidence matrix
- Network Topology: Branch-Loop incidence matrix
- Methods of Loop generation
Day 4
- Formulation of Equations for Steady-State Analysis
- Flow of Gases: Lacey Equation
- Flow of Gases: Polyfo Equation
- Flow of Gases: Panhandle ‘A’ Equation
- Flow of Gases: The Weymouth Equation
- Nodal Formulation
- Loop Formulation
- Gas Networks design:
- Newton-Nodal Method (Multi-dimensional Case)
- Newton-Nodal Method (One-dimensional Case—Hardy-Cross Method)
- Natural Gas Liquid Recovery and Gas for The Fuel Market
- Natural Gas Liquid
- Gas Absorpsion versus Fractionation
- Cooling in Gas Processing
- Gas Absorpsion/Stripping Cycles for Liquid Recovery
- Adsorption versus Absorption
- Expander Plant
- Conclusion
- Troubleshooting of Gas Networks
- Philosophy of Troubleshooting
- Troubleshooting of pipe line
- Troubleshooting of Compressor
- Troubleshooting of Control-Valves
INSTRUKTUR
Instruktur yang mengajar pelatihan NATURAL GAS ENGINEERING PROPERTIES ESTIMATION AND PIPE LINE NETWORK DESIGN FOR DISTRIBUTION AND PROCESSING ini adalah instruktur yang berkompeten di bidang NATURAL GAS ENGINEERING PROPERTIES ESTIMATION AND PIPE LINE NETWORK DESIGN FOR DISTRIBUTION AND PROCESSING baik dari kalangan akademisi maupun praktisi.
Jadwal pelatihan trainingmekatronika.com tahun 2024 :
- Batch 1 : 03 – 04 Januari 2024 | 16 – 17 Januari 2024
- Batch 2 : 07 – 08 Februari 2024 | 20 – 21 Februari 2024
- Batch 3 : 05 – 06 Maret 2024 | 19 – 20 Maret 2024
- Batch 4 : 09 – 10 April 2024 | 13 – 24 April 2024
- Batch 5 : 07 – 08 Mei 2024 | 22 – 23 Mei 2024
- Batch 6 : 05 – 06 Juni 2024 | 25 – 29 Juni 2024
- Batch 7 : 09 – 10 Juli 2024 | 23 – 24 Juli 2024
- Batch 8 : 06 – 07 Agustus 2024 | 20 – 21 Agustus 2024
- Batch 9 : 04 – 05 September 2024 | 18 – 19 September 2024
- Batch 10 : 18 – 19 Oktober 2024 | 15 – 16 Oktober 2024
- Batch 11 :06 – 07 November 2024 | 26 – 27 November 2024
- Batch 12 : 04 – 05 Desember 2024 | 18 – 19 Desember 2024
Catatan : Jadwal tersebut dapat disesuaikan dengan kebutuhan calon peserta training Pengenalan Natural Gas pasti jalan
Invetasi dan Lokasi pelatihan Penggunaan proses termodinamika di jogja :
· Yogyakarta,
· Jakarta,
· Bandung,
· Bali,
· Surabaya,
· Lombok,
Catatan : Apabila perusahaan membutuhkan paket in house training, anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan.
Fasilitas pelatihan Pengenalan Natural Gas di jogja :
- FREE Airport pickup service (Gratis Antar jemput Hotel/Bandara/Stasiun/Terminal)
- FREE Akomodasi ke tempat pelatihan bagi peserta training Penggunaan proses termodinamika jogja pasti running
- Module / Handout training Estimasi properti mekanik gas alam dan desain jaringan pipa untuk pendistribusian dan proses jogja fixed running
- FREE Flashdisk
- Sertifikat training Natural Gas Engineering Properties Estimation and Pipe Line Network Design for Distribution and Processing di jogja murah
- FREE Bag or bagpackers (Tas Training)
- Training Kit (Dokumentasi photo, Blocknote, ATK, etc)
- 2xCoffe Break & 1 Lunch, Dinner
- FREE Souvenir Exclusive
- Training room full AC and Multimedia
.