TRAINING PUMP & COMPRESSOR: CONTROL, OPERATION, MAINTENANCE & TROUBLESHOOTING
TRAINING PUMP & COMPRESSOR: KONTROL, OPERASI, PEMELIHARAAN & PEMECAHAN MASALAH
TRAINING CRITERIA FOR COMPRESSOR SELECTION
DESKRIPSI
The pump & compressor is a comprehensive course focusing on the fundamentals of centrifugal pumps and compressors. You will have an opportunity to discuss Pump/Compressor construction, design, operation, and maintenance and management issues and be provided with the most up-to-date information and best practice in dealing with the subject. Toward the end of the workshop, you will have developed the skills and ability to recognize and solve simple pump/compressor problems in a structured and confident manner.
TRAINING OBJECTIVES :
Participants will learn how to:
- Explain and understand pumps/compressor terminology
- Indentify various type of pumps/compressors
- Understand pumps/compressors characteristic and interpret pump/compressors curves
- Understand pump/compressors type and classification
- Understand Criteria for pump/compressors selection
- Perorm a number of simple pump/compressor calculation
- Confidently test and commission pump/compressor sets
- explain how pump/compressor are constructed
- Detail how to install, test and commission pump/compressor systems
- Explain how to start up a new pump/compressor or one after strip down for maintenance
MATERI
- . Introduction
- What constitutes a good a pump/compressor or compressor
- Safety
- Reliability
- Efficiency
- Risk consideration
- Life cycle cost consideration
- Overview of Statutory requirements
- . Centrifugal Pump and Construction
- Casings
- Impellers
- Axical/ radial forces
- Pump/compressor shafts
- Shaft seals – balances/unbalances, sea, wear patterns
- Drives and Coupling
- Support and Pipe connectionsAuxiliaries
- . Centrifugal Pump Characteristic and Operations
- Hydraulic properties of pump
- QH Curves
- PQ Curves
- Speed changes on curves
- . Pump Specification and selection
- System Analysis
- Data Sheets
- Bid Requests/ review/ analyses
- . Pump testing and inspection
- Material Inspection Requirements
- Shop Tests
- Performance Test Procedures
- Site Location
- Pump Foundations
- Associated Piping & Fittings
- Pre-operational Checks
- Operation of Pump
- . Pump Maintenance
- Pump breakdown and removal
- Single stage pump dismantling and repair
- Preparation for re-assembly
- Pump assembly
- Vertical and multistage pump repairs
- . Introduction to Compressors
- What is a compressor
- Basic criteria for compressor selection
- Compressor definitions
- . Reciprocating Compressors
- Principles and mechanics
- Definitions
- Part of a reciprocating compressor
- Maintenance of reciprocating compressors
- Performance of reciprocating compressors
- Mechanical Forces
- . Centrifugal Compressors
- Introduction
- Principle of Operational
- Operation
- Parts of Centrifugal compressor
- Casing configurations
- Types of compressors
- Performance of centrifugal compressor
- Polytropic compressor
- * Compressor control
WHO SHOULD ATTEND
The following selected participants should attend this course:
- Maintenance Engineer/ Superintendent/ Supervisor
- Rotating Engineer/ Superintendent/Supervisor
- Power Plant Engineer/Superintendent /Supervisor
- Manufacturing Manager
Everybody who wants to broaden knowledge and interest in this topics
INSTRUKTUR
Instruktur yang mengajar pelatihan PUMP & COMPRESSOR: CONTROL, OPERATION, MAINTENANCE & TROUBLESHOOTING ini adalah instruktur yang berkompeten di bidang PUMP & COMPRESSOR: CONTROL, OPERATION, MAINTENANCE & TROUBLESHOOTING baik dari kalangan akademisi maupun praktisi.
Metode:
Presentation, Discussion, Simulation, Case Study, Evaluation
Jadwal pelatihan trainingmekatronika.com tahun 2024 :
- Batch 1 : 03 – 04 Januari 2024 | 16 – 17 Januari 2024
- Batch 2 : 07 – 08 Februari 2024 | 20 – 21 Februari 2024
- Batch 3 : 05 – 06 Maret 2024 | 19 – 20 Maret 2024
- Batch 4 : 09 – 10 April 2024 | 13 – 24 April 2024
- Batch 5 : 07 – 08 Mei 2024 | 22 – 23 Mei 2024
- Batch 6 : 05 – 06 Juni 2024 | 25 – 29 Juni 2024
- Batch 7 : 09 – 10 Juli 2024 | 23 – 24 Juli 2024
- Batch 8 : 06 – 07 Agustus 2024 | 20 – 21 Agustus 2024
- Batch 9 : 04 – 05 September 2024 | 18 – 19 September 2024
- Batch 10 : 18 – 19 Oktober 2024 | 15 – 16 Oktober 2024
- Batch 11 :06 – 07 November 2024 | 26 – 27 November 2024
- Batch 12 : 04 – 05 Desember 2024 | 18 – 19 Desember 2024
Catatan : Jadwal tersebut dapat disesuaikan dengan kebutuhan calon peserta training Life cycle cost consideration pasti jalan
Invetasi dan Lokasi pelatihan criteria for compressor selection di bandung :
· Yogyakarta,
· Jakarta,
· Bandung,
· Bali,
· Surabaya,
· Lombok,
Catatan : Apabila perusahaan membutuhkan paket in house training, anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan.
Fasilitas pelatihan Life cycle cost consideration di bandung :
- FREE Airport pickup service (Gratis Antar jemput Hotel/Bandara/Stasiun/Terminal)
- FREE Akomodasi ke tempat pelatihan bagi peserta training criteria for compressor selection bandung pasti running
- Module / Handout training PUMP & COMPRESSOR: Kontrol, Operasi, Pemeliharaan & Pemecahan Masalah bandung fixed running
- FREE Flashdisk
- Sertifikat training PUMP & COMPRESSOR: Control, Operation, Maintenance & Troubleshooting di bandung murah
- FREE Bag or bagpackers (Tas Training)
- Training Kit (Dokumentasi photo, Blocknote, ATK, etc)
- 2xCoffe Break & 1 Lunch, Dinner
- FREE Souvenir Exclusive
- Training room full AC and Multimedia
.