TRAINING ALIGNMENT PUMP AND MOTOR
TRAINING FUNDAMENTAL ALIGNMENT
TRAINING MEASURING MISALIGNMENT
Description
Motor-Pump alignment is the process of aligning shaft centerlines between a motor and a pump. The motor is the prime mover, transferring power to the pump by the use of a coupling. This is probably the most common configuration of coupled machines in industry.
In this type of alignment, the motor is almost always the moveable machine, and the pump is the stationary machine. In almost all cases, the pump is already piped up with suction and discharge flanges, which means it can move only slightly, if at all.
motor-pump-alignmentProper shaft alignment is achieved by moving the motor. The motor is shimmed vertically to achieve the proper elevation to align it to the pump, both parallel (offset) and angular. The motor is them moved horizontally to achieve proper horizontal placement for aligning the shaft centerlines, both parallel and angular. The motor is moved horizontally by the use of jacking bolts, or by the use of pry bars, hammers, or other tools.
Motors are normally easier to move, since the motor is not piped into a process system. A short run of flexible conduit is most often used to run the electrical wiring from a local disconnect, or a rigid conduit, to the motor termination box. This allows for ease of movement of the motor.
Materi
1. Fundamental Alignment
2. Diagnosing Misalignment
3. Measuring Misalignment
4. Preparing Task Alignment
5. Alignment Methods (praktis)
•Rough Methods
•Face and Rim
6. Alignment Tolerances
7. Complicating Factor Alignment.
8. Introduction to Laser Alignment
9. Minimizes the forces of misalignment acting upon the bearings and seals of both components.
10. Minimizes Wear of The Coupling.
11. Reduce Energy Costs.
12. Maximizes the life of the Machine Components by Minimizing Wear, ncreasing time between failures, and reducing vibration.
Method
•Presentation
•Discussion
•Simulation
•Case Study
•Evaluation
Who Should Attend
Instrument Engineer/Supervisor, Plant Maintenance/Operators/Supervisors
Instructor
Mokhamad Munir Fahmi, Ir, MT. And Tim
(CV Terlampir)
Jadwal pelatihan trainingmekatronika.com tahun 2025 :
- Batch 1 : 30 – 31 Januari 2025
- Batch 2 : 13 – 14 Februari 2025
- Batch 3 : 11 – 12 Maret 2025
- Batch 4 : 16 – 17 April 2025
- Batch 5 : 15 – 16 Mei 2025
- Batch 6 : 25 – 26 Juni 2025
- Batch 7 : 16 – 17 Juli 2025
- Batch 8 : 6 – 7 Agustus 2025
- Batch 9 : 3 – 4 September 2025
- Batch 10 : 8 – 9 Oktober 2025 || 29 – 30 Oktober 2025
- Batch 11 : 13 – 14 November 2025 || 25 – 27 November 2025
- Batch 12 : 15 – 16 Desember 2025
Catatan : Jadwal tersebut dapat disesuaikan dengan kebutuhan calon peserta training Alignment Methods pasti jalan
Invetasi dan Lokasi pelatihan Measuring Misalignment di bandung :
· Yogyakarta,
· Jakarta,
· Bandung,
· Bali,
· Surabaya,
· Lombok,
Catatan : Apabila perusahaan membutuhkan paket in house training, anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan.
Fasilitas pelatihan Alignment Methods di bandung :
- FREE Airport pickup service (Gratis Antar jemput Hotel/Bandara/Stasiun/Terminal)
- FREE Akomodasi ke tempat pelatihan bagi peserta training Measuring Misalignment bandung pasti running
- Module / Handout training Fundamental Alignment bandung fixed running
- FREE Flashdisk
- Sertifikat training Alignment Pump and Motor di bandung murah
- FREE Bag or bagpackers (Tas Training)
- Training Kit (Dokumentasi photo, Blocknote, ATK, etc)
- 2xCoffe Break & 1 Lunch, Dinner
- FREE Souvenir Exclusive
- Training room full AC and Multimedia
.